カテゴリー: 産業用組込み向けパーツ

販売終了

X9DBU-iF

JAN/UPC:0672042101023
メーカー型番:MBD-X9DBU-IF-O
TEKWIND型番:SPM-MBD-X9DBU-IF-O/1Y

1. Dual socket B2 (LGA 1356) supports Intel® Xeon® processor E5-2400 v2
2. Intel® C602 chipset
3. Up to 768GB DDR3 1600MHz LRDIMM / 384GB RDIMM; 12x DIMM sockets
4. Riser card support:
Left side - 1x PCI-E 3.0 x24
Right side - 1x PCI-E 3.0 x8
5. Intel® i350 Dual port GbE LAN
6. 8x SATA2 and 2x SATA3 ports
7. Integrated IPMI 2.0 and KVM with Dedicated LAN
8. 8x USB 2.0 ports (2 rear + 4 via header + 2 Type A)

この製品を問い合わせる


スペック

Product SKUs

MBD-X9DBU-iF -B X9DBU-iF (Bulk Pack)

Physical Stats

Form Factor Proprietary UIO
Dimensions 12" x 13" (30.5cm x 33.0cm)

Processor/Cache

CPU Intel® Xeon® processor E5-2400   and E5-2400 v2 (up to 95W TDP **)
Dual Socket B2 (LGA 1356)
Cache Up to 25MB
System Bus QPI up to 8 GT/s
** Motherboard supports this maximum TDP. Please verify your system can thermally support

System Memory

Memory Capacity 12x 240-pin DDR3 DIMM sockets
Up to 768GB DDR3 ECC LRDIMM
Up to 384GB DDR3 ECC Registered memory (RDIMM)
Up to 96GB DDR3 ECC/non-ECC Un-Buffered memory (UDIMM)
Memory Type 1600/1333/1066/800MHz* ECC DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
Support ECC and non-ECC UDIMMs 

* Maximum memory speed may be capped by CPU. Please verify that the chosen CPU can support desired memory speed.
DIMM Sizes 32GB, 16GB, 8GB, 4GB, 2GB, 1GB
Memory Voltage 1.5 V, 1.35 V
Error Detection Corrects single-bit errors
Detects double-bit errors (using ECC memory)

On-Board Devices

Chipset Intel® C602 chipset
AHCI SATA SATA 2.0 3Gbps with RAID 0, 1, 5, 10
SATA 3.0 6Gbps with RAID 0, 1, 5, 10
SCU SATA SATA 2.0 3Gbps with RAID 0, 1, 5, 10
IPMI Support for Intelligent Platform Management Interface v.2.0
IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
Nuvoton WPCM450 BMC
Network Controllers Intel® i350 Dual Port Gigabit Ethernet
Virtual Machine Device Queues reduce I/O overhead
Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
1x Realtek RTL8201F PHY (dedicated IPMI)
Video Matrox G200eW

Input / Output

AHCI SATA 2x SATA 3.0 ports (6Gbps)
4x SATA 2.0 ports (3Gbps)
SCU SATA 4x SATA 2.0 ports (3Gbps)
LAN 2x RJ45 Gigabit Ethernet LAN ports
1x RJ45 Dedicated IPMI LAN port
USB 8x USB 2.0 ports total
(2 rear + 4 via header + 2 Type A)
Video 1x VGA port
Keyboard/Mouse PS/2 Keyboard/Mouse ports
Serial Port / Header 2x Fast UART 16550 ports / 1 rear and 1 header
DOM 1 DOM (Disk on Module) power connector
TPM 1 TPM 1.2 20-pin Header

Chassis (Optimized for X9DBU-iF )

1U Chassis CSE-113TQ-R500UB
CSE-813T-600UB
CSE-815TQ-R500UB
2U Chassis CSE-825TQ-R740UB
Tower / 4U Rackmount CSE-417E16-R1K28UB
CSE-417E26-R1K28UB
CSE-847A-R1K28UB
CSE-847E16-R1K28UB
CSE-847E26-R1K28UB
Important Chassis Notes To support the new generation Intel® Xeon® processor-based motherboards,Revision M chassis is recommended. Please talk to your sales representative for details.

SuperServer(s) with X9DBU-iF

Model(s) SYS-1027B-URF
SYS-6017B-NTF
SYS-6017B-URF
SYS-6027B-URF

Expansion Slots

PCI-Express 1x PCI-E 3.0 x24 (left hand side
riser card support)
1x PCI-E 3.0 x8 (right hand side
riser card support)

(Both CPUs need to be installed for full access to PCI-E slots and onboard controllers. See manual block diagram for details.)

System BIOS

BIOS Type 64Mb SPI Flash EEPROM with AMI BIOS
BIOS Features Plug and Play (PnP)
APM 1.2
PCI 2.3
ACPI 1.0 / 2.0 / 3.0 / 4.0
BIOS rescue hot keys
USB Keyboard support
SMBIOS 2.7.1
UEFI 2.3.1

Management

Software SuperDoctor® III
Watch Dog
NMI
IPMI 1.5 / 2.0
Power Configurations ACPI / APM Power Management
Power-on mode for AC power recovery

PC Health Monitoring

Voltage Monitors for CPU Cores, +1.1V, +1.5V, +3.3V, +5V, +12V, +3.3V Standby, +5V Standby, VBAT, 4 Memory Voltages.
5+1 Phase-switching voltage regulator
FAN 6x 4-pin fan headers with tachometer monitoring
Status monitor for speed control
Status monitor for on/off control
Low noise fan speed control
Pulse Width Modulated (PWM) fan connectors
Temperature Monitoring for CPU and chassis environment
CPU thermal trip support
Thermal Control for 6x Fan Connectors
Thermal Monitor 2 (TM2) support
PECI
LED CPU / System Overheat LED indicator
Suspend static indicator LED
UID/Remote UID
Other Features Chassis intrusion detection
Chassis intrusion header
SDDC Support
RoHS
Dual cooling zones

Operating Environment

Operating Temperature Range 10°C - 35°C (50°F - 95°F)
Non-Operating Temperature Range -40°C - 70°C (-40°F - 158°F)
Operating Relative Humidity Range 8% - 90% (non-condensing)
Non-Operating Relative Humidity Range 5% - 95% (non-condensing)

産業用組込み向けパーツに関連する導入事例

導入事例はありません。

産業用組込み向けパーツに関連する特集記事

特集記事はありません

(C) Tekwind Co., Ltd. ALL RIGHTS RESERVED.