カテゴリー: サーバー > ストレージサーバー

販売終了

SuperServer 6026TT-HTRF (Black) Rev2.0

JAN/UPC:0672042053803
メーカー型番:SYS-6026TT-HTRF_Rev2.0
TEKWIND型番:SPM-SYS-6026TT-HTRF

Four hot-pluggable systems (nodes) in a 2U form factor. Each node supports the following:

1. Intel® Xeon® processor 5600/5500 series, with QPI up to 6.4 GT/s
2. Up to 192GB** DDR3 1333/ 1066/800MHz ECC Registered DIMM / 48GB
Unbuffered DIMM
3. 1 (x16) PCI-E ( Low Profile)
4. Integrated IPMI 2.0 with KVM and Dedicated LAN
5. Dual Intel® 82574L Gigabit Ethernet Controller
6. 3x Hot-swap SATA Drive Bays
7. 1400W Gold-level High-efficiency Redundant Power Supplies

この製品を問い合わせる


スペック

Product SKUs

SYS-6026TT-HTRF SuperServer 6026TT-HTRF (Black)

Motherboard

4x Super X8DTT-HF+

Processor/Cache

CPU Dual 1366-pin LGA Sockets
Supports up to two Intel® 64-bit Xeon®processor(s) of the same type below:

Intel® Xeon® Processor X5600/E5600/L5600 Series
(Westmere) 40W - 95W


Intel® Xeon® Processor X5500/E5500/L5500 Series
(Nehalem-EP) 38W - 95W

 
QPI up to 6.4 GT/s

System Memory

Memory Capacity 12x 240-pin DIMM sockets
Supports up to 192 GB** 1333 / 1066 / 800MHz DDR3 ECC Registered memory
Supports up to 48 GB 1333 / 1066 / 800MHz DDR3 ECC / Non ECC Unbuffered memory
Memory Mirroring supported
Memory Type 1333 / 1066 / 800MHz ECC Registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
DIMM Sizes 1GB, 2GB, 4GB , 8GB** , 16GB**
Memory Voltage 1.5 V
Error Detection Corrects single-bit errors
Detects double-bit errors (using ECC memory)
Supports Intel® x4 and x8 Single Device Data Correction (SDDC)

On-Board Devices (per Node)

Chipset Intel® 5500 (Tylersburg) chipset
ICH10R + IOH-36D
SATA Intel ICH10R SATA 3.0Gbps Controller
RAID 0, 1, 5, 10 support
IPMI Support for Intelligent Platform Management Interface v.2.0
IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
Nuvoton WPCM450 BMC
Network Controllers Dual Intel® 82574L Gigabit Ethernet Controller
Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
1x Realtek RTL8201N PHY (dedicated IPMI)
Graphics Matrox G200eW
Super I/O Winbond W83527HG chip
Clock Generator 932S421 chip

Input / Output (per Node)

Serial ATA Six Serial ATA ports
3 SATA hard drives supported
LAN 2x RJ45 LAN ports
1x RJ45 Dedicated IPMI LAN port
USB 2 rear + 1 header (2 Ports)
4 total USB ports, 2.0 Compliant / 1.1 Compliant
VGA 1x VGA Port
Serial Port 1 Fast UART 16550 serial port

System BIOS (per Node)

BIOS Type 32Mb SPI Flash EEPROM with AMI® BIOS
BIOS Features Plug and Play (PnP)
PCI 2.2
ACPI up to 3.0
USB Keyboard support

Chassis

Form Factor 2U Rackmount
Model CSE-827H-R1400B

Dimensions

Height 3.5" (89mm)
Width 17.2" (437mm)
Depth 28.5" (724mm)
Gross Weight 85 lbs (38.6kg)
Available Colors Black

Front Panel (per Node)

Buttons Power On/Off button
UID button
LEDs Power LED (on power button)
Network activity LED
System Overheat/fan fail/power fail/ LED
UID LED (on UID button)

Expansion Slots (per Node)

PCI-Express 1 (x16) PCI-E ( Low Profile)

Drive Bays (per Node)

Hot-swap 3x 3.5" SATA Hot-swap drive bays

Hard drive Backplane

2U Hard drive Backplane

System Cooling

Fans 4x Cooling Fans

Power Supply

1400W high-efficiency (1+1) redundant power supply with PMBus
AC Input 1100W Output @ 100-140V, 13.5-9.5A, 50-60Hz
1400W Output @ 180-240V, 9.5-7.0A, 50-60Hz
DC Output 1100W: +12V/92A; +5Vsb/4A
1400W: +12V/116A; +5Vsb/4A
With Distributor +5V: 30 Amp
+3.3V: 24 Amp
-12V: 0.6 Amp
Certification Gold Level Certified
Gold Certified
Test Report ]

PC Health Monitoring

CPU Monitors for CPU Cores,+1.5V, +3.3V, +5V, +12V, +5 Stdby, +3.3 Stdby, VBAT, Memory Voltages.
CPU Core 6-Phase-switching voltage regulator
FAN Total of four 4-pin PWM fans
4x fans with tachometer monitoring
Status monitor for speed control
Status monitor for on/off control
Low noise fan speed control
Temperature Monitoring for CPU and chassis environment
CPU thermal trip support
Thermal Control for 4x Fan Connectors
PSU I2C temperature sensing logic
Thermal Monitor 2 (TM2) support
PECI
LED Power Fail / Overheat LED
Suspend-state Indicator LED
UID LED
Other Features SDDC Support

Operating Environment / Compliance

RoHS RoHS Compliant
Environmental Spec. Operating Temperature: 10°to 35°C (50°to 95°F)
Non-operating Temperature: -40°to 70°C (-40°to 158°F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)

(C) Tekwind Co., Ltd. ALL RIGHTS RESERVED.